Search:

If you like boiled shrimp you will love boiled bream, just boil them just like shrimp and dip in cocktail sauce
or use shrimp boil. Crappie will come apart but bream will stay firm.

I have a 13 hp john deer mower that has been used for that since 1999 when I got it. I just have a regular ball like you use on a vehicle on the back.
The frame in front was easy to extend with...

I kept 1 pound of minnows in two 5 gallon buckets alive from September until 2months ago. I changed about 1/3 of the water every 3 days and fed them
blue buffalo dry dogfood about every third day....

You might want to try the one that came with it, they get such great fuel mileage. If you don't want to try that, the dealer
should trade with you for a few bucks. The dealer mine came from offered...

Take it from someone that has had two different kinds. Minnkota!

I just looked it up, in july 2009 there were 200 rigs drilling for oil in the US. In march 2014 there were 1400 rigs drilling for oil. Seven times more than 5 years ago. Oil production has...

My reason for 3 wires is that if 12 volts is needed you have it. I would tie one of the bad wires down so it will stay in place then pull the other wire out. With the one wire that is in place tie...

You can get them from ebay most anytime in the $60 range!

I have a 1000 pack of wire ties and never thought of that, I also have a problem with loosing locks. Thanks

The fellow that bored it to .030 over, did the the cross hatch with a flexhone and it looked good. I started it and used about a 35 to one ratio of oil to gas, and run to hooked to muffs for about 20...

I did not take anyone with an aggressive slant it was taken as great info from every one that responded. I installed a complete gasket set along with new seals top and bottom, it
does not leak...

First road across the bridge going east , turn right on small dirt road that looks like it is going down to a couple of houses, the dirt launch is at the end of the road to the right. There is only...

In Courtland go north on spring creek road, turn right on cr 388 2 miles then launch boat into swoops pond on the right. It is down by some houses and kinda hard for a large boat.149240

Will check the wiring first, thanks for the idea!

I believe that is exactly what I needed it looks identical, Thanks a million !

The shutdown switch in the end or the tiller handle has stopped working. It is a 2000 25 hp mercury, does anyone know how to get that switch out and change it. It has to be an normally open switch...

I got her running, and it sure runs good. I put a picture of what could have been the cause of the failure according some of the info above.
The first picture is of the exhaust manifold gasket next...

I fish creeks a lot, if the wind ever gets up while in the creek and you have to go into larger rough water be prepared to get soaked or get at the back of the boat and manually
steer the boat with...

After the testing you have done there is probably some windings in the starter shorted, the voltage drop test will tell you if that is the case.
If there is a huge voltage drop when you try it that...

A friend had a 25 hp on his boat but with no gas tank and they made him get off the lake, so it might be a problem with any larger motor! They did not ticket him!

Thanks for all of the good info, I finally got it bored out .030 of an inch and came up with the parts.

Everything up to this point has gone well except it has taken a while for the parts to get...

Please let us know how you do, I live in decatur and would like to try it sometime!

Just did that exact thing the 4.80 is 16" tall and the 5.30 is 17.5" tall, the 5.30 is about 1/2 inch wider. So if you have an extra 3/4 inch of space you can do it.

Same luck here caught loads of crappie last fall at this time, but just cannot find them this year. Mostly fish Mallard, spring creek & flint creek.

Yes sir it is the bottom facing side!

This motor still had 100 lbs on the bottom cylinder and would start at the touch of the button and was still very powerful, Thanks to you guys and google I
have found a few of the parts need.

I believe that you might be on to something, The gasket on the deflection plate was all to pieces and there was quite a bit of oil just below it. If the recirculating hoses are those
2 small 1/8...

Anyone with knowledge of what caused this on the bottom piston only of a 25 mercury outboard. The top piston is in good shape with very little scarring.

144836

144837

Got it apart, the problem is only on the bottom cylinder, the rattling must have been the piston slapping. I hope to get by with boring it 20 over.

144834144835

Thanks for the info, I meant to call iboats today but didn't get around to it, they have very reasonably prices but no parts listed for below a 35 hp mercury.

Slabyanker, I have had 2 different...