Kroil is definitely some great stuff. Certainly has it's own very distinct smell
Last winter 2022-2023 I took this truck engine down to the short block. Since I bought this truck new back in 2001 I have tried to maintain its condition but with 244K miles on it the engine work was due. Previous unusual repairs, mainly the brake lines. Older Silverado truck's brake lines rust out. I had to replace all the lines so I did that using stainless steel. Under the hood I replaced everything, from the motor mounts up. Transmission lines, radiator, entire HVAC system, entire power steering system less the steering gear. All the sensors, electrical system, fuel system, the throttle body, ingition system, Hydro-boost & master cylinder, etc. All OEM GM parts. The heads didn't have a single exhaust valve that held a seal. I re-seated the valves myself before reinstalling the aluminum heads. The headlights, turn signals, even installed updated LED headlight bulbs. The brakes are all NAPA Fleet parts - Bullet Proof.
This job now is just shocks. Towing the Camper back from Ross Barnett for over-winter service and updating I could tell the truck body was rocking & bouncing too much.
First off removing the front wheel, a 22mm on the impact did the job.
The old shock has a thru bolt on the bottom the ones I received have a yoke mount on the bottom so I will post them installed Wednesday when the new ones arrive. These 2500HD's (this truck is the very first production run) have massive brakes, check out the size of the caliper.
A bit of penetrating spray on the threads and 2 19mm wrenches and the top nut was off.
So if you are planning on replacing the front shocks on a Sliverado or GMC truck check out how the bottom of your front shocks mount before ordering. Once you see the way your particular shock mounts check the part number of the shock you are ordering at the manufacturers website to confirm mounting. Most shock makers show a picture of the shock by part number. Here I didn't do it and apparently Chevrolet made more than 1 2500HD. I have the 9200# chassis which uses the bolt thru the eye securing the bottom of the shock.
The rear shocks are pretty straight forward to remove but on re-install a couple of problem quickly came up. To remove I just sprayed the bolt threads then removed the mounting bolts.
The upper shock mount was bent in from the mounting bolt mounting the original shock. I use a Jethro sized Crescent wrench to bend the tabs outward enough to allow not just the shock eye to clear but also the upper boot before installing the new shock.
Since these are gas charged there is a wire keeping the shock collapsed a bit so it can be easily installed. I just positioned my Mercedes floor jack under the lower shock mount and applied a little pressure to the mount before cutting the wire on the new shock. As the shock extended to the jack pad face I used a alignment bar to line up the holes to install the mounting bolt.
The upper boot was a bit of a pain to get around the top of the shock where it went before tightening the bolt and on the Driver's side I even had to lower the spare tire so I could get to the boot to attach the shock top properly.
Kroil is definitely some great stuff. Certainly has it's own very distinct smell
The love for fishing is one of the best gifts you can pass alongRojo LIKED above post
Wished I had your know-how. I'm still running my 2004 Z71 Chevy and hope it last me another 10-20 years. Mine has over 200K miles but a new engine went into 'er at 125K.
Health nuts are going to feel stupid someday, lying in hospitals dying of nothing.Rojo, BuckeyeCrappie LIKED above post
So with a LS based engine you can easily get 350K out of a bottom end but the oil pump, timing chain need to be done by 200K. I had already did what I call the Short List @ 200K miles. With 244K on the short block you could still see the original hone marks in the cylinder walls. None of the LS based engines I have ever seen had a traditional "Ridge" at the top of the cylinder regardless of miles. P-Nut tells me the older ones will crack the oil rings some how, dono. I have always did a 3K miles oil change running Mobil 1 or NAPA Pure Synthetic oils. Right now I'm doing a very tight job, can hardly get the phone in for a picture, replacing the Blend Door Motor in the dash of the Fishin' Expedition.
I was rolling on the Caddy getting all the mounting brackets ligned up when FedEx hit the door with the 2500HD Front Shocks. I did the Slidell Shuffle and switched to the truck.
After installing the shocks I made sure to Jam Nut the mounting hardware so nothing comes loose.
I needed a Stubby Ratchet because my wrists are giving me a bit of annoyance since they have basically be abused my entire working like. The Stubby makes running up the hardware much easier, still use a longer handle to torque with. This one is from Harbor Freight - ICON line. Feels fantastic, lots of teeth like a Snap-on, very reasonably priced for the quality. I'm liking their High Quality stuff. This one is 3/8 drive.
SuperDave336, S10CHEVY LIKED above post
I have some of the Icon stuff. Surely seem to be good tools
The love for fishing is one of the best gifts you can pass alongRojo LIKED above post
I went through very similar stuff with my old F250. Never considered a jam nut. Stored this in my memory banks for future reference.
“If your too busy to fish, you’re too busy!” Buddy Ebsen
PROUD MEMBER OF TEAM GEEZER
(Billbob and “G” approved!)
Proud member of Tekeum’s Jigs Pro
Staff
https://heavenornot.net/
heavenornot.netRojo thanked you for this post
So I grew up in Body Shops but never chopped a roof so this will be interesting. The camper is taking up all the room in the shop so it has to go back to Ross Barnett first before I start in on this project. I already have the word out for a used roof section & door. I figure if I can pick up a roof section I will buy a new OEM Roof Skin and use that to pull everything back in alignment enough the doors will work as well as seal.
I need covered parking and that is in short supply right now.
SuperDave336, S10CHEVY LIKED above post
…..
“If your too busy to fish, you’re too busy!” Buddy Ebsen
PROUD MEMBER OF TEAM GEEZER
(Billbob and “G” approved!)
Proud member of Tekeum’s Jigs Pro
Staff
https://heavenornot.net/
heavenornot.net