HaHa HaHa:  0
Results 1 to 6 of 6

Thread: 1994 Evinrude 60HP Compression problems. What should I do??

  1. #1
    Join Date
    Mar 2009
    Location
    Cockrum, MS
    Posts
    51
    Post Thanks / Like

    Default 1994 Evinrude 60HP Compression problems. What should I do??


    The compression in the 3 cylinders are: 125 , 110, 95. Engine cranks and runs fine otherwise. Plenty of power on water.

    What can I expect the cost of repairing to run me?

    I can't decide whether to find a used motor and possibly inherit someone else's headache or rebuild. I have no clue of what a rebuild would cost.

    I am in North MS.
    Life isn't about waiting for the storm to pass....It's learning how to fish in the rain!

  2. #2
    Join Date
    Mar 2020
    Location
    Rainbow City, AL
    Posts
    230
    Post Thanks / Like

    Default

    First thing I would do is a decarbon shock treatment with SeaFoam. Sometimes, you get lucky and that low compression in one cylinder is caused by carbon on the rings not allowing them to seat good. It will cost you less than $10 and you might get lucky.
    Likes NCkenner LIKED above post
    Thanks Bigwill thanked you for this post

  3. #3
    Join Date
    Jul 2017
    Location
    MO
    Posts
    982
    Post Thanks / Like

    Default

    Quote Originally Posted by Bigwill View Post
    Engine cranks and runs fine otherwise. Plenty of power on water.
    Doesn't sound like there's a problem to me. Run it.

    You could try decarbing, may help, may not.

    Unless you're doing the work yourself, probably more cost effective to swap in a used powerhead rather than have somebody rebuild it for you, unless the damage is so minor that rings and a hone will take care of it.

    You could pull the exhaust cover and look for scoring, but again, if it runs well, I wouldn't go looking for problems.
    Likes Bigwill, NCkenner LIKED above post

  4. #4
    Join Date
    Mar 2011
    Location
    Wisconsin
    Posts
    938
    Post Thanks / Like

    Default

    Quote Originally Posted by DoyleAlley View Post
    First thing I would do is a decarbon shock treatment with SeaFoam. Sometimes, you get lucky and that low compression in one cylinder is caused by carbon on the rings not allowing them to seat good. It will cost you less than $10 and you might get lucky.
    This is the first thing I would do those older Evinrude were notorious for carboning up the rings, they had a bad ring land design, from what happened to me as mine blew up. If the decarboning works move to a totally synthetic oil and this will help keep from building up carbon in the ring lands. Cheap 2 stroke dyno oil was what caused my problem according to my mechanic who rebuilt it using the newer style pistons.
    Thanks Bigwill thanked you for this post

  5. #5
    Join Date
    Mar 2020
    Location
    Rainbow City, AL
    Posts
    230
    Post Thanks / Like

    Default

    Quote Originally Posted by Bricks View Post
    This is the first thing I would do those older Evinrude were notorious for carboning up the rings, they had a bad ring land design, from what happened to me as mine blew up. If the decarboning works move to a totally synthetic oil and this will help keep from building up carbon in the ring lands. Cheap 2 stroke dyno oil was what caused my problem according to my mechanic who rebuilt it using the newer style pistons.
    Regardless of whether you choose to run cheap dino oil or expensive synthetic - running Sea Foam (or Yamalube Ring Free, etc.) as a preventative is cheap insurance. I run Sea Foam as a preventative in every small engine I own. Use at the rate of 1oz to about 10 gallons of gas as a preventative measure.
    Thanks Bigwill thanked you for this post

  6. #6
    Join Date
    Mar 2010
    Location
    Tipton Co TN
    Posts
    92
    Post Thanks / Like

    Default

    Those numbers are so close, I wouldn't worry. Definitely decarb. If after the decarb, the low cylinder doesn't come up, pull the head and put a straight edge on it. I have seen them warp before.

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

BACK TO TOP