Member rojoguio has article in OutdoorHub.com with SlabSauce

[Micanopy]

Cool…….. idea and cool that you were in an article.

I loved the way you made sure CrappiePappy was mentioned. First class.

[BuckeyeCrappie]

Good stuff!

[DockShootinJack]

The man never ceases to amaze me. From weld and fab, to boat rebuilding and let's not forget some of the most mouth watering cooking I have ever seen

[jammerman]

Wondering how much slab sauce you use in the mixture with worm oil and crappie
nibbles? Also is their a diiference
in worm oil brands? Thanks for any info .

[DWILL]

Great article thanks for sharing.

[Rojo]

Wondering how much slab sauce you use in the mixture with worm oil and crappie
nibbles? Also is their a diiference
in worm oil brands? Thanks for any info .

So I pour about 1/2 a bottle to a jar of Nibbles. The author was standing watching me mix but I didn't show how much oil I used. So after adding the Slab Sauce and a little oil I start mixing. I use Plasticizer oil for 3 reasons, first just like in cooking oil explodes the strength of the attractant, second to prevent the mixture from solidifying, and lastly oil is Hydrophobic so it does not easily wash off . When it will pass the epoxy syring tip with moderate pressure in my test syringe I load the other syringes about 1/2 full. It's a bit of a pain as you have to load the mixture from the back which traps air so I fill the syringe almost full and use a 1/16 TIG Stainless filler wire to work a air pocket on one side. this allows the air to exit thru the tip and I keep dispensing the attractant till the syringe is 1/2 full without any air pockets. If you leave air pockets just like a Caulk gun the compressed air will continue to dispense your attractant making a mess on top of wasting product. With one hand the distance from the finger tabs to the thumb on the plunger is not too great making it easier to use.

I use Plastizer or Worm oil not mineral oil not to say mineral oil wouldn't work. A bottle of Worm oil lasts a long time here.

[Jamesdean]

So I pour about 1/2 a bottle to a jar of Nibbles. The author was standing watching me mix but I didn't show how much oil I used. So after adding the Slab Sauce and a little oil I start mixing. I use Plasticizer oil for 3 reasons, first just like in cooking oil explodes the strength of the attractant, second to prevent the mixture from solidifying, and lastly oil is Hydrophobic so it does not easily wash off . When it will pass the epoxy syring tip with moderate pressure in my test syringe I load the other syringes about 1/2 full. It's a bit of a pain as you have to load the mixture from the back which traps air so I fill the syringe almost full and use a 1/16 TIG Stainless filler wire to work a air pocket on one side. this allows the air to exit thru the tip and I keep dispensing the attractant till the syringe is 1/2 full without any air pockets. If you leave air pockets just like a Caulk gun the compressed air will continue to dispense your attractant making a mess on top of wasting product. With one hand the distance from the finger tabs to the thumb on the plunger is not too great making it easier to use.

I use Plastizer or Worm oil not mineral oil not to say mineral oil wouldn't work. A bottle of Worm oil lasts a long time here.

Thank you for Sharing rojoguio. You da man...

[skeetbum]

Aaawwww geeeez! Now I gotta buy tubes!! I haven’t used em for a while but with gill bedding close I’m gonna want the advantage. Thanks Rojo, good diea.

[DockShootinJack]

Aaawwww geeeez! Now I gotta buy tubes!! I haven’t used em for a while but with gill bedding close I’m gonna want the advantage. Thanks Rojo, good diea.

I was thinking the same thing

[Rojo]

I see I didn't specify, 1/2 a bottle of Slab Sauce. You want it stiff but despensible, and I found the first one set up a little as it got older so don't make it too stiff to start. I walked into our local Walmart years ago and they had jars of Nibbles, the short ones, for 25c a jar. I bought them out so I don't know how old the ones I have actually are.