Thanks Thanks:  0
HaHa HaHa:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: SLA Battery Charging

  1. #1
    Join Date
    Feb 2021
    Location
    Richmond
    Posts
    47
    Post Thanks / Like

    Default SLA Battery Charging


    Hey all,

    Trying to figure this out. I'm attempting to charge my 12V, 7Ah batteries as shown, but they only ever get to a max of 12.6 volts per my Garmin 43 CV. Is there a change I should make in my charging TTPs? Thanks in advance for any input.
    Attached Images Attached Images  

  2. #2
    Join Date
    Sep 2012
    Location
    Dayton Tennessee
    Posts
    39,958
    Post Thanks / Like

    Default

    Settings look correct to me
    The love for fishing is one of the best gifts you can pass along

  3. #3
    Join Date
    Feb 2021
    Location
    Richmond
    Posts
    47
    Post Thanks / Like

    Default

    That's what I thought. I have another charger that gets them up to 12.9 volts every time, with what I'm pretty sure are the same settings. Would using the 10 amp setting for a short period of time help at all?

  4. #4
    CrappiePappy's Avatar
    CrappiePappy is offline Super Moderator - 2013 Man Of The Year * Crappie.com Supporter
    Join Date
    Apr 2004
    Location
    Lexington, KY
    Posts
    23,566
    Post Thanks / Like

    Default

    I'm an "idiot" when it comes to this kinda stuff .... BUT, how would a 7ah battery be considered "deep cycle" ?? My next concern would be .... is that charger the right one to use on a 7ah lithium battery ?? (assuming, of course, that the 7ah battery IS a lithium battery)

  5. #5
    Join Date
    Feb 2021
    Location
    Richmond
    Posts
    47
    Post Thanks / Like

    Default

    Quote Originally Posted by CrappiePappy View Post
    I'm an "idiot" when it comes to this kinda stuff .... BUT, how would a 7ah battery be considered "deep cycle" ?? My next concern would be .... is that charger the right one to use on a 7ah lithium battery ?? (assuming, of course, that the 7ah battery IS a lithium battery)
    I was told by a friend that they are indeed considered "deep cycle." Below is an example of the one I have, Sealed Lead Acid not lithium.

    https://www.academy.com/p/game-winner-12v-7-ah-rechargeable-battery

  6. #6
    Barnacle Bill's Avatar
    Barnacle Bill is offline Super Mod and 2014 Crappie.com Man of the Year * Crappie.com Supporter
    Join Date
    Apr 2004
    Location
    Chesapeake, Va
    Posts
    20,382
    Post Thanks / Like

    Default

    12.6 volts is a fully charged battery. When they get higher its just a surface charge and will go down pretty fast.
    Fair Winds and Following Seas

    Bill H. PTC USN Ret
    Chesapeake, Va

    Likes Cray LIKED above post

  7. #7
    Join Date
    Feb 2021
    Location
    Richmond
    Posts
    47
    Post Thanks / Like

    Default

    Quote Originally Posted by Barnacle Bill View Post
    12.6 volts is a fully charged battery. When they get higher its just a surface charge and will go down pretty fast.
    Great SA on this. So, is it normal for them to end up around 12.2 volts by the end of a trip that's a few hours long? The batteries I'd seen that started around 12.9 seemed to end up about 12.5 or so by the end of the same timeframe. Same kind of batteries with similar use histories

  8. #8
    Join Date
    Jun 2004
    Location
    SW Indiana
    Posts
    2,738
    Post Thanks / Like

    Default

    You can’t rely on the voltage reading of your electronics to determine battery state of charge. A meter on the battery terminals is the accurate way, or a 4-wire remote measurement to eliminate the voltage drop in the wiring.

    At the completion of charging and for several hours afterward or until you use the battery, you should see more than 13V on the battery. Because your battery is intended to be charged at 14.7V, it should measure 14.7V at the completion of charging assuming your charger doesn’t have a float stage. If your charger goes higher than 14.8V, it can damage the battery.

    Your battery is made by UPG, and their model number for it is UB1270. They don’t publish the open circuit voltage for it, but most AGMs run about 12.8-12.84V as the full charge voltage. Anything less and you aren’t at full charge.

    Your battery is not a deep-cycle battery for charging purposes. The deep-cycle switch on your charger is not really helpful, and I have doubts your charger is appropriate for an AGM and wouldn’t use it without verifying the output. You need 14.6-14.8V at no more than 2.1A to charge the battery.

  9. #9
    Join Date
    Feb 2021
    Location
    Richmond
    Posts
    47
    Post Thanks / Like

    Default

    Quote Originally Posted by CatFan View Post
    You can’t rely on the voltage reading of your electronics to determine battery state of charge. A meter on the battery terminals is the accurate way, or a 4-wire remote measurement to eliminate the voltage drop in the wiring.

    At the completion of charging and for several hours afterward or until you use the battery, you should see more than 13V on the battery. Because your battery is intended to be charged at 14.7V, it should measure 14.7V at the completion of charging assuming your charger doesn’t have a float stage. If your charger goes higher than 14.8V, it can damage the battery.

    Your battery is made by UPG, and their model number for it is UB1270. They don’t publish the open circuit voltage for it, but most AGMs run about 12.8-12.84V as the full charge voltage. Anything less and you aren’t at full charge.

    Your battery is not a deep-cycle battery for charging purposes. The deep-cycle switch on your charger is not really helpful, and I have doubts your charger is appropriate for an AGM and wouldn’t use it without verifying the output. You need 14.6-14.8V at no more than 2.1A to charge the battery.
    Got it, excellent info. So this appears to be my charger- is it not appropriate for charging said batteries? Would it help to switch it from "deep cycle" mode to "all others?"

    https://www.ebay.com/p/1234772570

  10. #10
    Join Date
    Jun 2004
    Location
    SW Indiana
    Posts
    2,738
    Post Thanks / Like

    Default

    Quote Originally Posted by VBSB761 View Post
    Got it, excellent info. So this appears to be my charger- is it not appropriate for charging said batteries? Would it help to switch it from "deep cycle" mode to "all others?"

    https://www.ebay.com/p/1234772570
    The only useful info I got from the manual for the charger is that the deep-cycle setting produces a higher voltage to the battery than the “all others” setting. But you need to know the actual voltage, and the manual doesn’t provide that info. Some older chargers supply output voltages that aren’t safe for AGM batteries.

Page 1 of 2 12 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

BACK TO TOP