Search:

im planning on doing some since i moved near hurricane creek landing.

just putting this out there have you thought of a auto latch device. something like:

Boat2Trailer | Boat Latch | Ramp N Clamp | Boat Load System

if you can power up to the latch itll lock in...

Oh he'll they opened you up good..
You'll be good just don't push the therapy..

I have a 85 50 hp evinrude I put in new reeds in myself . Got from a place in FL they asked me some questions and shipped them to me . Wasn't that big of a deal to replace the reeds..

Chris...

Well got it all done Thursday afternoon late forgot to take a pic before I put the toon back on , also got the new turn lights on it too..

427306
427307
Once I got them wet loaded hell a lot...

If yall think this needs to be moved to the main forum go ahead an move it wasn't thinking..

Got all the carpet off an staples out at 6pm I'm done for the nite..

427183

427178

This is on the back underneath see all the staple holes there were more staples on the stacked carpet on top of that.
I'm going to let the wood dry out tomorrow, i tested it it's solid. ...

Just got 1 board striped , guess the garmin not getting installed today .. I need a break any ways got to replace the short lag bolts holding the lumber into the frame. Luckily the white Jones...

Got my lineman pliers an needle nose so not too bad

Think someone had carpeted this before with comerial style , has like a backing to it just falling apart as I'm pulling it.
Guess all the staples and the weight of the pontoon was holding it on .

Ok yall pull all the staples out or pull what you can , then pound the break offs back in the wood to rust out??
This is soo freaking tedious I'm just 36 inches in 1 16 ft board an got 4 boards ��

Haven't been on the water, finally got a appt with a neurologist to see if my meds needs adjustment,. But let's see if I can get the bunks recovered today on for the toon tried yesterday at the boat...

I forget what the exact name is but i used to clean some motors i had with a electrical componet spray . Its non corossive and gives it a base protectant to it..
After you get all the big grime off..

I know comfirmed last nite, seems like shes wanting to get something too. No telling what it is..But imma tray an squeeze a new ipilot outta the deal too..:biggrin

its official ive forgotten how to fish out of a boat. went camping the other week got the grnkids on some fish from the bank, but when i went out on the toon nada.. Went out to Russell today 70 deg...

That is something

I'd like to know also

I've been looking at that for a bit shows that all the time . Might not have a oil tem sensor..

Well aren't yall with all the positive info. :bash

I'll have to check it out

Ok so your saying go with a 13 inch /11 pitch then

Ive just heard that if you hit something with the ss prop its not as forgiving as a aluminum prop..

not loaded just me the toon , motor 12 gal fuel and some fishing gear..
did some digging it has 120 deg tstat so block temp is correct..

Does having a SS prop really make a difference over aluminum

Ok its a 20 foot crest pontoon plate says max hp is 70hp. i have a 2004 60hp bigfoot motor. As far as weight just 1 12gal fuel tank , 3 batteries,toon alone is 1725lb motor is 225lb,and me 212lb and...

ok went back to the mercury site on my pc this time , looks hella different than on my phone. This what i came up with..

this for top speed
423744

this for fuel economy423745
both show same...

423743
This is my current prop only. 25 in diameter bigger same pitch as mercury recommended. So how much pitch to go down to get that 1k higher you think

Yes i have bout 4 years ago got a mean hybrid. Had like 6 lines out the back tangled the lot barely got it to the boat , jig was bout straighten out..was fun..

3 lb bass always fun on 4lb like and ultra lite rod