2013 Edge 1550 + Yamaha 25

**blueducklane** · 07-13-2019, 07:25 PM

2013 Waco Edge 1550 with custom interior design. Built by Tim Scott (and his wife) to comfortably accommodate a fishing or hunting trip, this design was a result of many hours of planning and measuring.

Engine detail: 1999 Yamaha 25 HP 3 cylinder, 2 stroke. Long shaft. Electric and manual start. New style big tiller. Tohatsu M40d carbs. Boyesen reeds. Power Tech SRA 3 blade, 13 pitch.

The interior includes a threaded seat base on the front and rear deck and is covered completely with Hydroturf. A conveniently located Marinco 12 volt outlet is installed on the front of the rear bench and a Marinco trolling motor plug is located on the bow and is wired with marine grade 6 gauge wire. Boat includes a MinnKota Maxxum 12 volt 55 lb trolling motor and a MinnKota quick release bracket. Also included is a heavy duty Ram Mount with a Lowrance Elite 7 HDI and transom transducer. Garage kept, one adult owner, located in W. Little Rock, AR.

$8000....PM for further detail.

Name: SB1.jpg
Views: 1071
Size: 214.6 KB

Name: SB1.jpg
Views: 1071
Size: 214.6 KB

Name: SB7.jpg
Views: 1073
Size: 221.7 KB

Name: SB2.jpg
Views: 1059
Size: 266.8 KB

Name: SB3.jpg
Views: 1102
Size: 264.5 KB

Name: SB4.jpg
Views: 1192
Size: 284.3 KB

Name: SB5.jpg
Views: 1052
Size: 295.9 KB

Name: SB8.jpg
Views: 1120
Size: 225.4 KB

Name: SB6.jpg
Views: 1030
Size: 243.6 KB

Name: SB9.jpg
Views: 1015
Size: 157.6 KB

Name: SB10.jpg
Views: 1007
Size: 144.2 KB

$8000.....PM for further details.

**huntinslabs** · 07-13-2019, 07:46 PM

Sweet rig. Just too dang far away for me to even ask price. Bet it dont last long at all.

**"D"** · 07-13-2019, 08:26 PM

Looks like that will make someone very happy. Does it have the second seat that matches the front one?

**blueducklane** · 07-14-2019, 08:13 AM

It does. The front seat (in the picture) is a Tempress high back mossy oak breakup boat seat. I have 2 of them that will go with the boat. Or if a buyer would prefer that Millenium seat on the rear bench it can go. Thanks for asking.

Sent from my iPhone using Crappie.com Fishing mobile app

**Crappieplasticm** · 07-15-2019, 01:35 PM

Would love to have that rig but a little steep for me

. What’s top end

**scout-j-m** · 07-16-2019, 03:52 PM

I just bought a 1988 30hp Yamaha Sunday that looks identical to that. May I ask how the tiller attaches? Also, I was told it had 40hp carbs but I don't even know what to look for to verify that. Mine unfortunately has a lower unit problem that didn't allow me to water test to get a feel for its speed or power, but it did allow me to get it for a really good deal.

**blueducklane** · 07-18-2019, 08:52 PM

The tiller attaches by sliding it over the existing 2 bolts that were used for the old tiller and nylock nuts hold the tiller in place. Eazy peazy japaneezy. Its size and length in particular provide the driver with much more control than the factory tiller and although i never installed a tilt and trim unit the tiller has the grip switch that can be wired up.

Scout j m - Your 40 carbs should be identical to mine.

Sent from my iPhone using Crappie.com Fishing mobile app