HaHa HaHa:  0
Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 23

Thread: Boat Accident....Need Advice

  1. #11
    Join Date
    Jan 2011
    Location
    North Carolina
    Posts
    4,279
    Post Thanks / Like

    Default


    You'll have to drill a hole in the bottom of that Lund to create a leak. They have double layers of aluminum sandwiching a gasket. That's the reason they are so much heavier than their competition.
    Thanks USMA65 thanked you for this post

  2. #12
    Join Date
    Oct 2010
    Location
    Sanford, NC
    Posts
    6,695
    Post Thanks / Like

    Default

    I agree with the others. Very likely no more than a valuable lesson and stress test for you and your central nervous system.
    You have been given a "do over" by a lesson that really didn't have a very high cost... this time... thankfully. Go fishin'.
    "Just Like Iron Sharpens Iron... So it is that One Man Sharpens Another Man." Proverbs 27:17
    Thanks USMA65 thanked you for this post

  3. #13
    Join Date
    Apr 1996
    Location
    Central Florida
    Posts
    25,900
    Post Thanks / Like

    Default

    I’m certainly no expert but I agree with the others. IMHO you didn’t do any damage to that boat at all. They’re tougher than you think. Especially a Lund.


    Sent from my iPhone using Crappie.com Fishing mobile app
    Owner
    "Wear your PFD" "No texting n driving" slab
    Crappie.com members are the best
    Thanks USMA65 thanked you for this post

  4. #14
    Join Date
    May 2015
    Location
    Missouri
    Posts
    217
    Post Thanks / Like

    Default

    You will be good to go as others have mentioned! Lesson learned tho!!
    Your transducer will be fine, if it was properly installed that is how they are designed incase you hit something. Sounds like it performed as it was supposed to.

    I got caught out in a storm with no time to load one evening so I just beached it and tied off to a tree. It rained buckets that night to the fact that I had to go down every couple hours and run the bilge pump, no big deal BUT the wind blew like crazy and the waves pushed my 2070 Xpress up on the bank in the pea gravel and literally "sanded" all the paint off the bottom of my boat!! I was SICK......
    My HDSI transducer looked like I had drug it down a gravel road as it didn't have enough force to "kick" it up like it was designed to do. I took it off and used a series of sand paper and just kept sanding/wet sanding until I got it back somewhat slick again! I am actually still using it today and works perfect.
    Thanks USMA65 thanked you for this post

  5. #15
    Join Date
    Oct 2013
    Location
    TEXAS
    Posts
    21,055
    Post Thanks / Like

    Default

    I am in the ouch ,don't do that again crowd . if you were at a some speed it might really hurt , but on a boat ramp mostly just feelings and paint is likely the final outcome .
    sum kawl me tha outlaw ketchn whales
    Thanks USMA65 thanked you for this post

  6. #16
    Join Date
    Sep 2008
    Location
    Central Florida
    Posts
    2,772
    Post Thanks / Like

    Default

    Just like the current/future saga of the Pandemic illustrates...Life's events, whether personally created or not, should always yield to a new found awareness modus operandi!

    u2s
    Thanks USMA65 thanked you for this post

  7. #17
    Join Date
    Jan 2019
    Location
    Las Cruces NM
    Posts
    97
    Post Thanks / Like

    Default

    I did worse, much worse. With a roller trailer and all the boat on the ramp.
    Brand darn new boat too. Only third time out. Insurance totaled boat. But, not motor. Couldn't get a new boat without a new motor. What was I going to do with two Yamaha 90 four strokes. Aluminum and Pontoon Boat Repair in Texas fixed it. Of course that was two trips to N Texas from NM. You were lucky, Very very lucky!
    Learn Grasshopper Learn.
    Last edited by "G"; 06-11-2020 at 06:22 PM.
    Likes "G" LIKED above post
    Thanks USMA65 thanked you for this post

  8. #18
    skeetbum's Avatar
    skeetbum is offline Crappie.com Legend - Moderator Jig Tying Forum * Crappie.com Supporter
    Join Date
    Dec 2007
    Location
    Florida
    Posts
    22,922
    Post Thanks / Like

    Default

    I’m getting here late , but as a former Lund owner and the way their seams are built, I would have been surprised if it leaked. I bought mine at 25 years old and sold it four years later and it never leaked a drop. No water no where. The motor and ducer may have had an issue but I see that they’ve checked out so far. Lesson learned. As already said, your boat then you make sure it’s road ready yourself, every time.
    Creativity is just intelligence fooling around
    Thanks USMA65 thanked you for this post

  9. #19
    Join Date
    May 2012
    Location
    Millington,Tennessee
    Posts
    686
    Post Thanks / Like

    Default

    That's why I would never use rollers or the neoprene pieces that goes on top of the bottom bunks.
    I may be getting older but I refuse to grow up.
    Likes Mbsbeek LIKED above post
    Thanks USMA65 thanked you for this post

  10. #20
    Join Date
    Oct 2019
    Location
    Cameron N.C.
    Posts
    882
    Post Thanks / Like

    Default

    Just curious how did safety chain not hold ?
    Thanks USMA65 thanked you for this post

Page 2 of 3 FirstFirst 123 LastLast

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

BACK TO TOP