SLABSAUCE Crappie Attractant |
Likes Likes:  0
Results 1 to 6 of 6

Thread: Finally got the 2.5 hp Merc motor started - problem solved: where to put the t.m.

  1. #1
    Join Date
    Feb 2005
    Location
    Walden, NY
    Posts
    2,159
    Post Thanks / Like

    Default Finally got the 2.5 hp Merc motor started - problem solved: where to put the t.m.

    My aluminum 10' Lowe's flat bottom V is very stable. Much of the time I can stand in it when casting. But this was before I bought the 2.5 hp Merc. Once the starting problem was solved by a local mechanic, the next problem is where to put the trolling motor.

    I was concerned that the battery and heavy 4-stroke would weigh the transom down to much when I sat on the back seat not to mention the 45# thrust Minn Kota tm. Since I've always used a handle extension for the tm to be able to sit in the middle seat, I couldn't see myself twisted around handling it along with the gas motor. Besides, the extension handle can not be used when both motors are side-by-side on the transom.

    Solution: attach a thin board with screws just up from the oar lock to take the tm bracket. Aluminum is thin and the stress was too much without the wood. I can still use the oars and swivel the tm in any direction (extension not needed) while sitting in the middle seat.

    The tm is tilted horizontal to the water when the gas motor is running and the gas motor is tilted with prop out of the water in shallow water when fishing to avoid stumps, rocks, weeds, etc. The combined weight of the tm battery, gas motor and me on the back seat still allows a nice speed with little transom dip.

    If I use my 12' flat bottom boat, I will have to figure out where to put the tm other than the very front due to a metal handle in the way. Most likely a side mount also. The 10' is easier to load so I use it when fishing solo.

  2. #2
    Join Date
    Sep 2012
    Location
    Dayton Tennessee
    Posts
    17,496
    Post Thanks / Like

    Default

    Sounds like an awesome set up to fish from
    :I would like to thank the builders of docks for giving me a place to fish and lose tackle

  3. #3
    Join Date
    Feb 2005
    Location
    Walden, NY
    Posts
    2,159
    Post Thanks / Like

    Default

    Thanks.
    In my area all other lakes are electric only. This particular lake I use to fish from my old bass boat and know it well. The lake is also the largest water of the 8 waters and to get from one end to the other takes about 50 min. with the tm/ now only 10 min. with the Merc. The advantage using a shallow-draft boat is I can go shallower and work the wetlands closer to shore than heavier boats are capable of.

    Hopefully this little 4 stroke won't take much gas as my 90 hp 2-stroke did considering the increase in fuel price. But then again my 2003 Chevy truck is lucky if it gets 16 mpg. I don't want to guess how much it will cost to fill the 26 gal. tank.

  4. #4
    Join Date
    Sep 2012
    Location
    Dayton Tennessee
    Posts
    17,496
    Post Thanks / Like

    Default

    It is liable to make gas. I downsized from a 2 stroke 150 down to a 4 stroke 60. The boat with the 150 had a 30 gallon tank and may have gotten a mile to the gallon. The 4 stroke has a 13 gallon tank and you have to go a long ways to burn 5 gallons
    :I would like to thank the builders of docks for giving me a place to fish and lose tackle

  5. #5
    Join Date
    Feb 2005
    Location
    Walden, NY
    Posts
    2,159
    Post Thanks / Like

    Default

    Good to know. The .3 gal. gas tank should be good for 3 round trips and hopefully not use much oil.

  6. #6
    Join Date
    Sep 2012
    Location
    Dayton Tennessee
    Posts
    17,496
    Post Thanks / Like

    Default

    Once broke in it shouldn't use any oil unless there is a problem
    :I would like to thank the builders of docks for giving me a place to fish and lose tackle
    Thanks Spoonminnow thanked you for this post

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

BACK TO TOP