HaHa HaHa:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 17

Thread: Boat Battery Tech Tips

  1. #1
    Barnacle Bill's Avatar
    Barnacle Bill is offline Super Mod and 2014 Crappie.com Man of the Year * Crappie.com Supporter
    Join Date
    Apr 2004
    Location
    Chesapeake, Va
    Posts
    20,299
    Post Thanks / Like

    Default Boat Battery Tech Tips


    POINTS TO REMEMBER
    The battery is the heart of the electrical system. Always start troubleshooting at the battery. Never store a battery in a discharged state. Never add anything except distilled water to a battery.

    IMPORTANT BATTERY FACTS
    A good battery can provide four or five years of worry-free service with the right kind of care. Bigger is better! The battery you are replacing does not have to be the same size as the original. It is always better to have extra battery capacity.

    DRY CHARGED BATTERIES MUST BE CHARGED BEFORE USING
    Many small batteries are supplied with the electrolyte in a separate container. If you have to fill a new battery with electrolyte, you must place the battery on a quick charger. The charging system will never bring the battery to a fully charged state. The battery capacity will never be above 80%. Pulling the battery out later and trying to charge it will not work. The battery’s capacity has been permanently cut by 20% and there is nothing you can do about it.

    BATTERIES WILL SELF DISCHARGE WHEN STORED
    Batteries will self discharge when stored for long periods of time. This is a normal process with all lead acid batteries. Always charge the battery to full charge before storing. Also disconnect the negative battery able. This will keep the small system drains from accelerating the discharge process. The best way to avoid hortened battery life is use a SMART CHARGER (not a trickle charger) that will maintain the battery at a full state of charge by only charging the battery when the voltage drops to a specified level without overcharging.

    ELECTROLYTE BECOMES WATER IN A DISCHARGED BATTERY
    As a battery becomes discharged the percentage of sulfuric acid in the electrolyte becomes less. The sulfuric acid combines with the lead plates producing lead sulfate. As this happens the electrolyte solution becomes pure water. A discharged battery will freeze in cold climates, which will destroy the insulators and plates inside it.

    LOOSE BATTERY TERMINAL ENDS CAN DESTROY A BATTERY
    Loose or corroded battery cable lugs can cause all sorts of problems. When the starter is engaged the loose or corroded connection can cause a heavy arc which will melt the post right out of the battery. If the battery is gassing, the arc can cause the battery to explode. Never use the temporary type battery ends. These are only good for emergency use and will become corroded in a short period of time. Always use a crimped and
    sealed battery cable end or replace the battery cable.

    BATTERY TESTING PROCEDURES

    WARNING! Batteries give off hydrogen gas constantly. Hydrogen gas is highly explosive. Always wear safety glasses or goggles and use caution when working with batteries.

    OPEN CIRCUIT VOLTAGE TEST
    Before you can properly test any battery it must be at FULL CHARGE. You can verify the state of charge with the use of a digital multimeter. Connect the digital multimeter to the battery terminals. A fully charged 12 volt battery will read at least 12.6 volts (2.1 volts per cell) on the multimeter. If your reading is 12.4 OR BELOW you must recharge the battery before testing.

    Open Circuit Volts / Percent of Charge
    11.7 volts or less / 0%
    12.0 / 25%
    12.2 / 50%
    12.4 / 75%
    12.6 or more / 100%

    LOAD TESTING THE BATTERY
    Before you can properly test any battery it must be at FULL CHARGE.
    The only way you can thoroughly test a battery is to place a high amperage load across the battery terminals.

    Starter motors have very high amperage requirements which can exceed 300 amps on certain engine applications. If the battery has to be recharged you must first remove the surface charge. This can be done by using the starter. Disable the ignition spark (consult manufacturer’s method to avoid electronic ignition) and crank the engine for 10-15 seconds. Once you have removed the surface charge, disconnect the battery cables and connect the battery load tester to the battery posts.

    Determine the cold cranking amperage rating of the battery you are testing. If the cold cranking amp rating (CCA) is not known, use 450 CCA for four cylinder engines, 550 CCA for six cylinder engines and 650 CCA for V-8 engines.

    Adjust current draw on the load tester to 50% of the CCA rating. Continue this for 15 seconds while viewing the voltage reading on the battery tester. The voltage should stay above the specified reading (see chart below) without falling off. If the voltage remains at the specified level or above, the battery would be considered good. If the voltage reading drops below the specified level, replace the battery.

    Load Test Chart
    Minimum Voltage / Temperature
    9.6 / 70 F 21C and above
    9.5 / 60F 16C
    9.4 / 50F 10C
    9.3 / 40F -1C
    9.1 / 30F -7C
    8.9 / 20F -12C
    8.7 / 10F -18C
    8.5 / 0F -18C

    This information is from the ARCO Starting and Charging Catalog which can be found on this website.



    Fair Winds and Following Seas

    Bill H. PTC USN Ret
    Chesapeake, Va


  2. #2
    CrappiePappy's Avatar
    CrappiePappy is offline Super Moderator - 2013 Man Of The Year * Crappie.com Supporter
    Join Date
    Apr 2004
    Location
    Lexington, KY
    Posts
    23,481
    Post Thanks / Like

    Default

    Here's another site with some good technical info on batteries : Deep Cycle Battery FAQ

    ... cp

  3. #3
    Join Date
    Aug 2011
    Location
    na
    Posts
    2,174
    Post Thanks / Like

    Default

    Very good info on batteries. Thanks for posting it up for everyone.
    Thanks jiggingman2020 thanked you for this post

  4. #4
    Join Date
    Mar 2011
    Location
    MS
    Posts
    1,329
    Post Thanks / Like

    Default

    You guys are GREAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAT! as my boye Tony would say keep up the info!!!!!!!!!!!!!!

  5. #5
    Join Date
    Apr 2004
    Location
    Alexandria, KY
    Posts
    1,104
    Post Thanks / Like

    Default

    My boat has set all Summer and now into fall. I have kept the batteries charged during the summer. Now that fall and cold weather has arrived I plugged in by on board charger and both batteries are down. One side showing redline, the other nothing, black. So I discconnected the on board charger and plugged in my 15amp shumacher marine charger and charged up my trolling motor deep cycle battery. It says after charging 6 hrs. at 10amps, it is 100%. So I plug in the starting battery and charge for 6 hrs and it says it is 100%. Next day plug in my onboard charger and both are showing full red line on both batteries. I leave them charging overnite and yesterday morning both have green lights, showing fully charged. Is this normal??? Or are my batteries shot because they didn't hold charge or is this normal?? How do I check them for voltage if they are charged at 100% without taking them out of the boat?
    Thanks,
    Bassky

  6. #6
    Barnacle Bill's Avatar
    Barnacle Bill is offline Super Mod and 2014 Crappie.com Man of the Year * Crappie.com Supporter
    Join Date
    Apr 2004
    Location
    Chesapeake, Va
    Posts
    20,299
    Post Thanks / Like

    Default

    After they are fully chagred disconnect them and let them sit for 24 hours. Then using a digital meter measure the voltage(s).
    Name:  voltchart1.gif
Views: 5979
Size:  6.3 KB
    Fair Winds and Following Seas

    Bill H. PTC USN Ret
    Chesapeake, Va


  7. #7
    Join Date
    Apr 2004
    Location
    Alexandria, KY
    Posts
    1,104
    Post Thanks / Like

    Default

    Bill,
    My batteries tested at 12.67 and 12.66, so they must be OK. I measured a full 24 hrs after charging. Thanks for the table and suggestions.
    Bassky
    Likes jiggingman2020 LIKED above post

  8. #8
    Join Date
    Oct 2012
    Location
    Texas
    Posts
    106
    Post Thanks / Like

    Default

    Good info, Thanks for the post.
    2005 War Eagle, 50hp Mercury 4 stroke

  9. #9
    Join Date
    Nov 2011
    Location
    Oklahoma
    Posts
    645
    Post Thanks / Like

    Default

    Thanks for the chart and tips

  10. #10
    Join Date
    Oct 2012
    Location
    Texas
    Posts
    106
    Post Thanks / Like

    Default

    ttt
    2005 War Eagle, 50hp Mercury 4 stroke

Page 1 of 2 12 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

BACK TO TOP