Likes Likes:  0
Thanks Thanks:  0
HaHa HaHa:  0
Results 1 to 3 of 3

Thread: Planer Board Maintenance

  1. #1
    Join Date
    Jun 2009
    Location
    Leslie
    Posts
    4,396
    Post Thanks / Like

    Default Planer Board Maintenance


    If you are anything like me (most fisherman are) you don’t own one of something, you own ten! I hate being on the water, the fish are ripping a particular lure like there is no tomorrow, and you only have one of them on board. When it comes to fishing lures, I buy two of everything. It is a good rule to live by. You never know when you will find the next hot bait at some tackle stand at a mom and pop gas station in Michigan’s Upper Peninsula. You usually purchase one with the hopes that “it might work” only to find out that it was some crazy custom color created by Uncle Larry who has long since retired.

    Unlike fishing lures however, many of us fall far from the path when it comes to other gear in our boats. A prime example of this is our planer board clips. Many guys have the original clips on their boards with no extras on board. As time goes on, the pads get worn down, the pins get clipped off, they become brittle due to cold use cycles, and people are left with equipment that doesn’t function properly. Having an extra supply onboard can be the difference between a successful trip and one that ends with endless trips turning around to pick up lost boards, premature releases, or a lost board entirely.

    For me, I carry a rather large supply of extra Off Shore Tackle OR16 (red) clips on hand. I not only use them on the tail of my Off Shore boards but also to affix drop weights and Off Shore Guppy weights. When I have a new clip, I always start them out in their light position. This is done by adjusting the spring inside of the clip to its rear location. As the clips start to wear in, I might have to adjust them to their stronger setting (spring in the front). I always check for pin damage and also for pad wear. The majority of the time, I run OR19 (orange) clips on the front of all of my Off Shore planer boards. I start each day off with the spring setting in the loose position. If I start to find that wind and waves are causing premature line releases, I might adjust the springs to their heavier setting. If this still doesn’t fix the issue, it is usually caused by a worn down pad and I will change out to a new clip.

    During the off season I go through all of my OR16 and OR19 clips and replace any worn pads. I also inspect my OR16 clips for pin wear. One little trick that I have picked up over the years is learning how to properly store my clips. When they are not in use, I like to slide a tiny piece of wax paper in between the pads. This ensures that direct heat or sunlight will not allow the pads to stick together. Although I have seen regular paper used, it is often prone to absorbing moisture and water. This is why I prefer to use wax paper.

    Replacement parts are available from Off Shore Tackle in order to change out your pads on the OR16 and OR19 clips. For the OR16 (red) clips you will need Off Shore Model # HRRP16HL. For the OR19 (orange) clips you will need Off Shore Model # HRRP16
    Attachment 296929

    There are a few pieces of equipment I utilize in order to make the process a lot easier. I use a pinch style bar clamp, a flat file, a small flat head screw driver, a razor blade or other thin metal object, and super glue.
    Attachment 296930

    Utilizing the flat file, I take my mini screwdriver and file down the end of it so that it is sharp. I utilize this tool to remove the old pads and scrape any excess glue from the old surface. To hold the Off Shore Clips in place, I set the spring at its lightest tension setting (spring in the back) and pinch it together with the clamp. This opens the clip and allows me to work on it without constantly pushing it together with my fingers.
    Attachment 296931

    Once the clamp is open I use the screwdriver tool I created in order to remove the old pads and scrape any extra glue from the surface. Be careful not to damage the pins on your OR16 (red) clips.
    Attachment 296932

    Once removed you should have a clean surface to affix your new pad.
    Attachment 296933

    For the OR19 (orange) clips, I put a small dab of superglue in the middle of the pad. Just enough so that when it is pushed down the glue doesn’t ooze out of the edges. For the OR16 (red) pads, I put tiny drops around the open hole (usually 4 total)
    Attachment 296934

    You can use a set of forceps, tweezers, or your fingers to put the pad inside the cavity. Flip the clip over and complete the other side. Once you are down, put your razor blade in between the pads and release your pinch clamp. This will provide even pressure on your pads without having them stick together due to any extra glue that might squeeze out.
    Attachment 296935

    After a couple of minutes you can remove the razor and add your wax paper. For the OR16 (red clips) I do NOT utilize the razor for pressure. I use wax paper between the pads and allow the pressure of the clip to do the job. This ensures that the pads get proper pressure, the pins don’t get covered with glue, and the pads do not stick together.

    Having properly functioning clips on board can mean all the difference in the world when you start running in to issues where your boards are slipping, you are getting premature releases, or you start to lose boards in the water.
    Attached Images Attached Images        
    I have OCD "Obsessive Crappie Disorder"

  2. #2
    Join Date
    Mar 2012
    Location
    Eaton County, Michigan
    Posts
    3,021
    Post Thanks / Like

    Default

    Very good article Rich, hopefully someone will "archive it"

    I bought my first 4 pair of boards about 8-9 years ago, since added 2 more. However fishing/trolling with you, mine have seen very little water time and are still like new. Maybe that will change this year when you "kick me out of the nest" and I fly solo......which is good and bad, cause I have so much fun trolling with you and your dad.
    2017 MiCDC fall crappie guide of the year (FCGOTY)
    Member: “Michigan chapter of Team Overalls
    Haulin Ash Fishing Rocks-"D"
    Caution: If we fish together, you may be on YouTube

  3. #3
    "G"'s Avatar
    "G" is offline Super Duper Moderator - 2012 Crappie.Com Man of the year & 2018 Crappie.com Decade of Exceptional Service Awards * Crappie.com Supporter * Member Sponsor
    Join Date
    Aug 2008
    Location
    Belden, MS
    Posts
    95,225
    Post Thanks / Like

    Default

    Quote Originally Posted by Just Steve View Post
    Very good article Rich, hopefully someone will "archive it"
    I am working on that
    I have spent most my life fishing........the rest I wasted.
    PROUD MEMBER OF TEAM GEEZER
    PICO Lures Field Rep

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

BACK TO TOP